Sandvik 7RE10 (Billets)
Datasheet updated 2013-03-22 15:43:48 (supersedes all previous editions)
Sandvik 7RE10 is an austenitic, stainless chromium-nickel steel of the 25/20 type. It has good resistance to carburisation, sulphidation and oxidation combined with moderate creep strength and structural stability. maximum service temperature in air is 1100°C (2010°F).
Standards
- ASTM 310S, 310H
- UNS S31008, S31009
- EN number 1.4845
- W.Nr. 1.4845
- DIN X12 CrNi 25 21
- SS 2361
- AFNOR Z12CN25-20
- BS 310S31
Product standards
ASTM A-314
Suitable for production of flanges etc. acc. to ASTM A-182
Certificates
Status according to EN 10 204/3.1
Chemical composition (nominal) %
| C |
Si | Mn | P max |
S max |
Cr | Ni | Mo | Others |
|---|---|---|---|---|---|---|---|---|
| 0.05 | 0.5 | 1.3 | 0.030 | 0.010 | 24.5 | 21 | - | - |
Forms of supply
Sizes and tolerances
Round-cornered square, as well as round billets, are produced in a wide range of sizes according to the following tables. Larger sizes offered on request.
Surface conditions
Square billets
Unground, spot ground or fully ground condition.
Round billets
Peel turned or black condition.
| Size | Tolerance | Length |
|---|---|---|
| mm | mm | m |
| 80 | +/-2 | 4 - 6.3 |
| 100, 114, 126, 140, 150 | +/-3 | 4 - 6.3 |
| 160, 180, 195, 200 | +/-4 | 4 - 6.3 |
| >200 - 350 | +/-5 | 3 - 5.3 |
Sizes and tolerances apply to the rolled/forged condition.
| Size | Tolerance | Length |
|---|---|---|
| mm | mm | m |
| 75 - 200 (5 mm interval) | +/-1 | max 10 |
| >200 - 450 | +/-3 | 3 - 8 |
| Size | Tolerance | Length |
|---|---|---|
| mm | mm | m |
| 77 - 112 (5 mm interval) | +/-2 | max 10 |
| 124, 134 | +/-2 | max 10 |
| 127, 147, 157 | +/-2 | max 10 |
| 142, 152, 163 | +/-2 | max 10 |
| 168, 178, 188 | +/-2 | max 10 |
| 183, 193 | +/-2 | max 10 |
Other products
- Hollow bar
- Welding wire
- Covered electrodes
Mechanical properties
At 20°C
| Proof strength | Tensile strength | Elong. | Hardness | ||
|---|---|---|---|---|---|
| Rp0.2a | Rp1.0a | Rm | Ab | A2" | HRB |
| MPa | MPa | MPa | % | % | |
| min. | min. | min. | min. | max. | |
| 220 | 240 | 515-750 | 35 | 35 | 90 |
At 68°F
| Proof strength | Tensile strength | Elong. | Hardness | ||
|---|---|---|---|---|---|
| Rp0.2a | Rp1.0a | Rm | Ab | A2" | HRB |
| ksi | ksi | ksi | % | % | |
| min. | min. | min. | min. | max. | |
| 32 | 35 | 75-109 | 35 | 35 | 90 |
1 MPa = 1 N/mm2
a) Rp0.2 and Rp1.0 correspond to 0.2% offset and 1.0% offset yield strength, respectively.
b) Based on L0 = 5.65 √S0 where L0 is the original gauge length and S0 the original cross-section area.
At high temperatures
|
Temperature
|
Proof strength
|
|
|---|---|---|
| Rp0.2 | Rp1.0 | |
| °C | MPa | MPa |
| min | min | |
| 50 | 200 | 230 |
| 100 | 190 | 220 |
| 150 | 180 | 210 |
| 200 | 170 | 200 |
| 250 | 165 | 195 |
| 300 | 160 | 190 |
| 350 | 155 | 185 |
| 400 | 150 | 180 |
| 450 | 145 | 175 |
| 500 | 140 | 170 |
| 550 | 135 | 165 |
| 600 | 130 | 160 |
| 650 | 125 | 155 |
|
700
|
120
|
150
|
Disclaimer: Recommendations are for guidance only, and the suitability of a material for a specific application can be confirmed only when we know the actual service conditions. Continuous development may necessitate changes in technical data without notice. This datasheet is only valid for Sandvik materials.
Article functions
Related information
Print this datasheet
Export to PDF
Download this datasheet as PDF or send by email.
Download as PDF
Send PDF via email